Your cart
FiiO i1

FiiO i1

$69.00

Keeping your favourite 3.5mm Headphones Around

The FiiO i1 is an Apple MFi certified, digital-to-analog convertor (DAC) and headphone amplifier designed for the Lightning connector. The digital audio signal enters through the Lightning connector end that can be connected to the Apple iPhone/iPod/iPad (and other Apple products), while the analog audio signals are pushed out through the 3.5mm output. The i1 also atomically detects if you are using a standard headphone or one with in-line controls. Just because Apple has ditched the headphone jack doesn't mean you have to ditch your favourite headphones.

High-Performance DAC Chip for Better Quality than iPhone's Stock DAC

Within the i1 is a high quality chip with both a DAC and a headphone amplifier. Not only does this chip support lossless audio formats, as well as achieve a high signal-to-noise ratio and low distortion, it also supports high-definition voice calls to give you crystal-clear conversations anytime, anywhere. (The i1 currently only supports up to lossless 48kHz audio due to the Lightning Audio Module(LAM) -  this may change to up to 192 kHz pending changes to the LAM.)

High-quality Microphone that Clearly Captures Your Voice

Built into the i1 is a high-sensitivity microphone that ensures your voice is clearly heard during calls and recordings - no more miserable conversations due to poor voice quality.

Feel at Home with a Familiar Layout

Since the i1 shares the same button layout as the stock Apple headset, you can immediately start using it without any hassles. The i1 further improves on the Apple headset with larger buttons with more tactile feedback, allowing you to complete actions more easily and quickly.

Controll All with Your Fingers

The three-button design of the i1 allows you to effortlessly pause, play, and switch tracks, as well as answer the phone, adjust the volume, and a number of other operations. Just gently press the buttons with your fingers and you will find that you have no need to even take out your Apple product, ensuring it stays pristine and undamaged.

Simply Plug-and-Play

the i1 automatically knows when it is plugged in and when it is pulled out of your Apple device for truly seamless operation. No need to worry about nay interference noise when connecting and disconnecting to your Apple product or when switching tracks -just plug it in and enjoy your music!

A Dedicated Companion App at Your Service

FiiO has a team specifically dedicated to maintaining a dedicated iOS app for the i1 for fast and convenient firmware upgrades in the future.

Quick Wake Up but no Wasted Electricity

When your Apple iOS device does into standby, the i1 will automatically fall into a lower power consumption mode. You can also set the i1 to go into standby mode and/or sleep mode after a certain period of time to reduce the power used by the i1, and save it for your Apple device. You can even wake up your Apple device through the i1by pressing the play/pause button - and you can wake up the i1 from your Apple device too.

Compatible with a Wide Range of Music Apps and Formats

The i1 not only supports iTunes, it is also compatible with many other music apps, including (but not limited to): Spotify, Tidal and Apple Music. A total of 9 music formats are supported, including AAC (from 8 to 320 kbps), protected AAC files from the iTunes store, Apple Lossless (ALAC), and AIFF. You can be sure that you can listen to your favourite songs, no matter which format they are in.

Specifications

 Weight about 11.5g
Input Interface MFi standard lightning plug
Output interface 3.5 mm stereo jack
Supported USB Sample Rate Lossless 48kHz (may change to up to 192kHz pending changes to the LAM)
THD+N <0.003%
Output Impedance <1 ohm (32 ohms loaded)
Dimensions 45.5mm in length, 9.5mm in diameter
Cable Length 80cm / 7cm
CODEC Chip NAU88L25
Output Power 30 mW (15 ohms loaded)
Frequency Response 20Hz - 20kHz